Post Reply 
HP41CL Secondary MMU Lockup
08-27-2021, 05:56 PM (This post was last modified: 08-27-2021 06:02 PM by Howard Owen.)
Post: #1
HP41CL Secondary MMU Lockup
I dusted off my old 41CL yesterday and was playing around with the secondary MMU settings. I accidentally swapped in an undefined configuration and the calculator locked up. Removing the batteries for a time got me a MEMORY LOST. After that, executing "MMUDIS MMUCLR "YFNZ" PLUG1L MMUEN locks up the calculator again. Have I bricked my expensive tech toy?

P.S. This is v5 hardware. The YFNZ version is 4G


Regards,
Howard
Find all posts by this user
Quote this message in a reply
08-27-2021, 06:09 PM
Post: #2
RE: HP41CL Secondary MMU Lockup
I have tried very hard to brick my 41CL and I was not able to do so permanently. Wink

Do another Memory Lost and redo your commands, it should works.
If not, remove the batteries, {wait for ... see period below}, insert the batteries and redo your commands, it should works, if not, use a longer wait period.
Wait period: 1 minute, 1 hours, 1 day, 1 week

Sylvain

PS: On a standard 41C/CV/CX I use a paper clip to short the first and last battery connector in the 41 case, but I do not remember if the trick works on the 41CL.
Find all posts by this user
Quote this message in a reply
08-27-2021, 06:23 PM
Post: #3
RE: HP41CL Secondary MMU Lockup
Thanks for your quick reply!

(08-27-2021 06:09 PM)Sylvain Cote Wrote:  Do another Memory Lost and redo your commands, it should works.
Repeating the steps results in the same outcome. I've tried four or five repetitions, varying the configuration slightly.

(08-27-2021 06:09 PM)Sylvain Cote Wrote:  If not, remove the batteries, {wait for ... see period below}, insert the batteries and redo your commands, it should works, if not, use a longer wait period.
Wait period: 1 minute, 1 hours, 1 day, 1 week

One minute suffices to get me back to MEMORY LOST. I'm currently in the first one hour wait period to see if that improves things.


Regards,
Howard
Find all posts by this user
Quote this message in a reply
08-27-2021, 07:12 PM
Post: #4
RE: HP41CL Secondary MMU Lockup
Howard,
I am assuming that no physical modules is plugged at the back.
Have you tried "YFNX" instead of "YFNZ" ?
Sylvain
Find all posts by this user
Quote this message in a reply
08-27-2021, 07:41 PM
Post: #5
RE: HP41CL Secondary MMU Lockup
Howard,

Maybe your problem is with the 41CL system RAM at page 0x804.

You can brute force a complete clear of the 41CL with the following:
Code:
MMUDIS          // disable MMU
"801000-0000"   // alternate memory 1 address & reset value
YMCLR           // clear alt-mem-1
"802000-0000"   // alternate memory 2 address & reset value
YMCLR           // clear alt-mem-2
"803000-0000"   // alternate memory 3 address & reset value
YMCLR           // clear alt-mem-3
"804000-0000"   // internal memory & reset value
YMCLR           // clear internal memory
"800000-0000"   // main memory address & reset value
YMCLR           // clear main-mem & creating a memory lost

Sylvain
Find all posts by this user
Quote this message in a reply
08-27-2021, 08:23 PM
Post: #6
RE: HP41CL Secondary MMU Lockup
(08-27-2021 07:12 PM)Sylvain Cote Wrote:  Howard,
I am assuming that no physical modules is plugged at the back.
Have you tried "YFNX" instead of "YFNZ" ?
Sylvain

Oddly enough, loading YFNX seems to have fixed the problem.


Regards,
Howard
Find all posts by this user
Quote this message in a reply
09-05-2021, 05:28 AM
Post: #7
RE: HP41CL Secondary MMU Lockup
And Sylvain strikes again!

Good one.
Find all posts by this user
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 2 Guest(s)