HP35s Entering complex number arguments

08202015, 10:41 PM
Post: #1




HP35s Entering complex number arguments
I feel that I am missing something, but I am struggling to enter nontrivial arguments for complex numbers in RPN mode on the HP35s. For example, how would I enter something like "5 theta pi"? When I try it the obvious way, I get a syntax error. Or if I would like to do something like "2*2 + 4i"?
Is there a way to use the value of the stack registers as the arguments for complex numbers? I am also not able to use stored values for the arguments for complex numbers. I really hope there is a simple way to do this, and that I do not have to write programs to do simple things like this, something that I am completely unfamiliar with. BR, 

08212015, 05:58 AM
(This post was last modified: 08212015 05:59 AM by Dieter.)
Post: #2




RE: HP35s Entering complex number arguments
(08202015 10:41 PM)Merwedv Wrote: For example, how would I enter something like "5 theta pi"? When I try it the obvious way, I get a syntax error. Or if I would like to do something like "2*2 + 4i"? I do not have a simple solution for the theta case, but the latter is simple and rather straightforward: 2 [ENTER] 2 [x] 4 [i] [+]. Assuming the calculator is set to RPN mode. In ALG mode you simply type "2x2+4i". ;) (08202015 10:41 PM)Merwedv Wrote: Is there a way to use the value of the stack registers as the arguments for complex numbers? Sure. If the real and complex parts are in Y and X, simply press [i] [x] [+] to get y+ix. (08202015 10:41 PM)Merwedv Wrote: I am also not able to use stored values for the arguments for complex numbers. This can be done in the same way: [RCL] B [i] [x] [RCL] A [+] Or, saving one stack register: [i] [RCL][x] B [RCL][+] A. Dieter 

08212015, 09:05 PM
(This post was last modified: 08212015 09:17 PM by Merwedv.)
Post: #3




RE: HP35s Entering complex number arguments
Hi Dieter,
Thanks so much for your response. It does seem very obvious now that you clarified. I was regarding "i" as a operand, rather than an actual number, albeit complex, and that completely threw me off the right track. (led astray by the xiy notation). As for "r /_ theta", since it is merely a shorthand of r*e^(j*theta), it is neither an operand nor a "number"(like i) and cannot be treated as such. I spend some time learning how to program the thing (not as difficult as I anticipated), and did the following to be able to use the X and Y registers to enter a complex number in the r /_ theta notation: Code:
So it will take the Yreg as the magnitude, and the Xreg as the angle, and place the complex result in Xreg, in either rectangular or polar notaion, depending on the diplay mode. Cheers, Merwe 

08212015, 10:03 PM
Post: #4




RE: HP35s Entering complex number arguments
(08212015 09:05 PM)Merwedv Wrote: Why don't you simply put it on a single line (and save one stack register)? Code: REGY*COS(REGX)+i*REGY*SIN(REGX) You may also define this as an equation, so a simple EQN ENTER will turn X and Y into a complex number. However, I would prefer a stack drop like this: Code: T T Which may be implemented in a short program this way: Code: LBL A Dieter 

08242015, 09:14 AM
Post: #5




RE: HP35s Entering complex number arguments
Yeah, your way is much better. Thanks again.


« Next Oldest  Next Newest »

User(s) browsing this thread: 1 Guest(s)