Post Reply 
Completely turning off HP Prime
11-09-2020, 03:14 AM
Post: #1
Completely turning off HP Prime
Hi everyone,

Does anyone know how do I turn off HP Prime G2? I mean, turning it off completely, not in standby mode with Shift+On (Shift+Off).

The issue is, that I use it extensively for a week and then have a break for 1-2 months. During that time the calculator discharges itself and I have to charge it. This seems to damage the battery in the long term considerably, because it's often sitting in my shelf at 0% charge and then I charge it to 100% when I notice.

I checked the manuals, official pages, but to no avail.

Is there a way to turn the calculator off completely, similar to turning off your phone?

Thanks.
Find all posts by this user
Quote this message in a reply
11-10-2020, 01:35 AM (This post was last modified: 11-10-2020 01:36 AM by Joe Horn.)
Post: #2
RE: Completely turning off HP Prime
Yes. What you want is called "Coma Mode" (different from "comma mode"). It puts your Prime into such a deep sleep that it's in a virtual coma, using almost no power at all. The batteries last much longer in coma mode than in normal off mode.

The easiest way to go into coma mode is:
(1) Press and keep holding down the Shift key.
(2) Press and hold down the On key for at least one second (very important!).
(3) Release both keys.

To exit coma mode, simply press On and wait a few seconds. The delay might scare you... it always makes me fear that the Prime has crashed... but it's normal. Just be patient, and it'll power up.

<0|ɸ|0>
-Joe-
Visit this user's website Find all posts by this user
Quote this message in a reply
11-10-2020, 02:24 AM
Post: #3
RE: Completely turning off HP Prime
(11-10-2020 01:35 AM)Joe Horn Wrote:  Yes. What you want is called "Coma Mode" (different from "comma mode"). It puts your Prime into such a deep sleep that it's in a virtual coma, using almost no power at all. The batteries last much longer in coma mode than in normal off mode.

The easiest way to go into coma mode is:
(1) Press and keep holding down the Shift key.
(2) Press and hold down the On key for at least one second (very important!).
(3) Release both keys.

To exit coma mode, simply press On and wait a few seconds. The delay might scare you... it always makes me fear that the Prime has crashed... but it's normal. Just be patient, and it'll power up.
You know Joe, it is kind of scary how you know all of this information seemingly off of the top of your headSmile
Visit this user's website Find all posts by this user
Quote this message in a reply
11-10-2020, 06:32 AM
Post: #4
RE: Completely turning off HP Prime
After some time (one or two days?) The G2 automatically switches to Coma Mode.

— Dirk Hartland
Find all posts by this user
Quote this message in a reply
11-10-2020, 07:06 AM
Post: #5
RE: Completely turning off HP Prime
@Joe Horn: Thanks, it seems to behave exactly as you described!

The fun thing is, that I have intuitively done this many times, but was waiting for some confirmation message on exit on or boot, and I haven't noticed the difference in boot time because it's very subtle (~1 sec compared to ~3 seconds).
Find all posts by this user
Quote this message in a reply
10-23-2023, 09:09 AM
Post: #6
RE: Completely turning off HP Prime
I know this is an old thread but just in case it's of interest to anyone browsing through....

According to this review...

https://www.cemetech.net/forum/viewtopic...35&start=0

... the Prime will also switch itself into Coma mode automatically 3 days after a normal switch off.
Find all posts by this user
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 1 Guest(s)