Post Reply 
Is that, where we go to?
04-26-2014, 09:42 PM (This post was last modified: 04-26-2014 10:17 PM by HP-Collection.)
Post: #1
Is that, where we go to?
See #161271280751 on TAS......
In former time I could buy relally good stuff here....
It's time to find a new hobby Wink
Visit this user's website Find all posts by this user
Quote this message in a reply
04-26-2014, 09:46 PM
Post: #2
RE: Is that, where we go to?
(04-26-2014 09:42 PM)HP-Collection Wrote:  See #161271280751 on TOS......
In former time I could buy relally good stuff here....
It's time to find a new hobby Wink

Smile

I'm done with the old one. Didn't find another one, though.

Greetings,
    Massimo

-+×÷ ↔ left is right and right is wrong
Visit this user's website Find all posts by this user
Quote this message in a reply
04-26-2014, 09:47 PM (This post was last modified: 04-26-2014 11:38 PM by rprosperi.)
Post: #3
RE: Is that, where we go to?
(04-26-2014 09:42 PM)HP-Collection Wrote:  See #161271280751 on TOS......
In former time I could buy relally good stuff here....
It's time to find a new hobby Wink

At $1.99/each, it's a good thing they are in "good condition"!

--Bob Prosperi
Find all posts by this user
Quote this message in a reply
04-26-2014, 10:13 PM
Post: #4
RE: Is that, where we go to?
Um... that should say TAS, not TOS. TOS (The Other Site) is run by Warren Furlow and is specifically related to the HP-41.

http://WilsonMinesCo.com (Lots of HP-41 links at the bottom of the links page, http://wilsonminesco.com/links.html )
Visit this user's website Find all posts by this user
Quote this message in a reply
04-26-2014, 10:14 PM
Post: #5
RE: Is that, where we go to?
"For parts" I get it, but "not working"? that looks like a working screw to me! Smile Actually this is a not too bad HP fetish. You might need a screw for your 45 and this saves you the expense of a Vernier. Screws are tricky... The price per gram of 45 is out of market though Smile (and 20$ for shipping a screw to Spain is just great)
Find all posts by this user
Quote this message in a reply
04-26-2014, 10:16 PM
Post: #6
RE: Is that, where we go to?
That's the seller that located a "golden zebra" for Aurelio. She's going through some tough times. Perhaps you could cut her some slack.

Dave
Find all posts by this user
Quote this message in a reply
04-26-2014, 10:28 PM
Post: #7
RE: Is that, where we go to?
(04-26-2014 10:16 PM)Dave Frederickson Wrote:  That's the seller that located a "golden zebra" for Aurelio. She's going through some tough times. Perhaps you could cut her some slack.

Dave

Now I feel bad Blush Now seriously, this is a reasonable auction. The price is probably right (shipping here is not), it could well be higher. It's a thread in jest, no offence intended.
Find all posts by this user
Quote this message in a reply
04-26-2014, 10:54 PM
Post: #8
RE: Is that, where we go to?
There does seem to be an increasing trend of reducing vintage HPs to their fundamental quanta for sale. I suspect that most of the calculators broken down in this way were not fully functional. Tearing apart a single kaput calculator to serve as an organ donor to enable the restoration of many others seems like a noble sacrifice.

John
Find all posts by this user
Quote this message in a reply
04-26-2014, 11:57 PM (This post was last modified: 04-26-2014 11:59 PM by jebem.)
Post: #9
RE: Is that, where we go to?
Yap, the worst thing that can possible happen when rebuilding a machine is to find out that one tiny screw is missing...
Of course there are plenty of screw replacements in the market. For that asking price I can get a box of them. But then I would know, and nothing is better than the original one, isn't it?

Jose Mesquita
RadioMuseum.org member

Find all posts by this user
Quote this message in a reply
04-27-2014, 12:52 AM
Post: #10
RE: Is that, where we go to?
(04-26-2014 11:57 PM)jebem Wrote:  Yap, the worst thing that can possible happen when rebuilding a machine is to find out that one tiny screw is missing...
Of course there are plenty of screw replacements in the market. For that asking price I can get a box of them. But then I would know, and nothing is better than the original one, isn't it?

I would think with the community of collectors/repairers and hackers in this forum, we could relinquish small parts like this when need for that critical restoration.

I would! Lord knows I have a few loose (HP) screws....
Find all posts by this user
Quote this message in a reply
05-02-2014, 01:47 AM
Post: #11
RE: Is that, where we go to?
Hi Matthais,

I "see" your screw and raise you a used rudder (sic) foot. TAS Item 151292708883.

It's the same seller and I truly feel sorry for her, but I couldn't help myself.

Dave
Find all posts by this user
Quote this message in a reply
05-02-2014, 08:10 AM
Post: #12
RE: Is that, where we go to?
(05-02-2014 01:47 AM)Dave Frederickson Wrote:  Hi Matthais,

I "see" your screw and raise you a used rudder (sic) foot. TAS Item 151292708883.

It's the same seller and I truly feel sorry for her, but I couldn't help myself.

Dave

And six pictures to show it from all sides... Dodgy

Greetings,
    Massimo

-+×÷ ↔ left is right and right is wrong
Visit this user's website Find all posts by this user
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 1 Guest(s)