HP Forums / HP Calculators (and very old HP Computers) / General Forum v / [FRAM71] Pre-Production Batch

Post Reply 
[FRAM71] Pre-Production Batch
06-09-2015, 10:55 PM (This post was last modified: 06-09-2015 11:27 PM by Dave Frederickson.)
Post: #134
Dave Frederickson Offline
Senior Member
 		Posts: 2,186
Joined: Dec 2013
RE: [FRAM71] Pre-Production Batch
I removed the zero ohm resistors, R10 and R11, on my FRAM71 that connect VJTAG and VPUMP to 3.3V. Made a new cable that connects pins 6 and 7 on the FlashPro4. This connects the 3.3V VPUMP generated on the FlashPro4 to the VPUMP and VJTAG on the FPGA and VJTAG on the FlashPro4.

Flashed V502 then V510 again. No problems. The warning message went away, too. Smile

Note: The LT1521-3.3 regulator in the FlashPro4 can provide 300mA.

Dave
Find all posts by this user
Quote this message in a reply
Post Reply 


Messages In This Thread
ROM Images - Dave Frederickson - 12-10-2014, 03:51 AM
IRAM vs ROM - Dave Frederickson - 12-13-2014, 06:36 PM
ROMCOPY - Dave Frederickson - 12-20-2014, 08:59 PM
[FRAM71] Bankswitching? - Hans Brueggemann - 02-07-2015, 06:55 PM
v430 beta - Dave Frederickson - 02-16-2015, 06:09 AM
RE: [FRAM71] Pre-Production Batch - cruff - 02-11-2015, 11:45 PM
v430 beta - Dave Frederickson - 02-17-2015, 05:14 AM
v430 beta - Dave Frederickson - 02-27-2015, 05:20 AM
1MByte FRAM71 - Dave Frederickson - 03-14-2015, 09:18 PM
RE: [FRAM71] Pre-Production Batch - Gene - 03-15-2015, 02:04 AM
V501 Firmware woes - Hans Brueggemann - 04-23-2015, 07:12 PM
Eagerly awaiting mine - cruff - 04-24-2015, 12:40 AM
RE: [FRAM71] Pre-Production Batch - cruff - 04-24-2015, 12:53 PM
Received my FRAM71 today! - cruff - 04-25-2015, 07:03 PM
RE: [FRAM71] Pre-Production Batch - cruff - 04-26-2015, 12:27 PM
RE: [FRAM71] Pre-Production Batch - Erwin - 10-04-2016, 08:28 PM
MEMBUF - Dave Frederickson - 05-13-2015, 02:50 AM
FRAM71 V502 - Hans Brueggemann - 05-16-2015, 04:02 PM
RE: [FRAM71] Pre-Production Batch - Erwin - 01-02-2016, 08:13 AM
RE: [FRAM71] Pre-Production Batch - Oulan - 06-03-2015, 02:10 PM
RE: [FRAM71] Pre-Production Batch - Oulan - 06-03-2015, 03:47 PM
RE: [FRAM71] Pre-Production Batch - Oulan - 06-05-2015, 09:44 AM
RE: [FRAM71] Pre-Production Batch - Oulan - 06-08-2015, 07:13 AM
RE: [FRAM71] Pre-Production Batch - Dave Frederickson - 06-09-2015 10:55 PM
FlashPRO - Dave Frederickson - 06-11-2015, 03:42 PM
RE: [FRAM71] Pre-Production Batch - cruff - 06-13-2015, 12:04 PM
RE: [FRAM71] Pre-Production Batch - cruff - 06-15-2015, 11:22 PM
Blinkin' Lights - Dave Frederickson - 07-15-2015, 03:07 AM
FRAM71 LED - Hans Brueggemann - 07-16-2015, 11:47 AM
RE: [FRAM71] Pre-Production Batch - Andres - 01-25-2016, 10:40 PM
RE: [FRAM71] Pre-Production Batch - Erwin - 10-04-2016, 08:46 PM
RE: [FRAM71] Pre-Production Batch - Erwin - 10-04-2016, 09:04 PM



User(s) browsing this thread: 1 Guest(s)

Contact Us | The Museum of HP Calculators | Return to Top | Return to Content | Lite (Archive) Mode | RSS Syndication