05-22-2014, 06:36 AM
05-22-2014, 06:39 AM
GTO.057
05-22-2014, 07:05 AM
(05-22-2014 06:39 AM)Thomas Klemm Wrote: [ -> ]GTO.057Nice. Thanks Thomas :-)
05-22-2014, 09:12 AM
FYI, please see p. 98 (of 244) of the manual.
d:-)
d:-)
05-22-2014, 01:26 PM
(05-22-2014 09:12 AM)walter b Wrote: [ -> ]FYI, please see p. 98 (of 244) of the manual.
d:-)
My manual has got only 211 pages (v3.1)...
Anyhow, that solution only works in input mode, because when in program mode we have to navigate using just the up and down arrows, right?
I do not see this a big issue, however it was nice if we could do page up and page down as well from inside the program editor.
05-22-2014, 02:11 PM
(05-22-2014 01:26 PM)jebem Wrote: [ -> ](05-22-2014 09:12 AM)walter b Wrote: [ -> ]FYI, please see p. 98 (of 244) of the manual.
d:-)
My manual has got only 211 pages (v3.1)...
You don't want me to specify the respective pages for v3.0, v2.2, etc., do you?
(05-22-2014 01:26 PM)jebem Wrote: [ -> ]Anyhow, that solution only works in input mode, because when in program mode we have to navigate using just the up and down arrows, right?
I do not see this a big issue, however it was nice if we could do page up and page down as well from inside the program editor.
That solution works in run mode. When in program mode, how about pressing [P/R] [GTO][.] xyz [P/R] ?
d:-)
P.S.: And Franz is right.
05-22-2014, 09:05 PM
(05-22-2014 02:11 PM)walter b Wrote: [ -> ]Of course not(05-22-2014 01:26 PM)jebem Wrote: [ -> ] My manual has got only 211 pages (v3.1)...
You don't want me to specify the respective pages for v3.0, v2.2, etc., do you?
I do my home work, so before posting my remark I did check my copy of the freeware pdf downloadable Owner's Guide v3.1.
By the way, the information on the GTO command is on page 87 of 211.
(05-22-2014 02:11 PM)walter b Wrote: [ -> ](05-22-2014 01:26 PM)jebem Wrote: [ -> ]Anyhow, that solution only works in input mode, because when in program mode we have to navigate using just the up and down arrows, right?
I do not see this a big issue, however it was nice if we could do page up and page down as well from inside the program editor.
That solution works in run mode. When in program mode, how about pressing [P/R] [GTO][.] xyz [P/R] ?
P.S.: And Franz is right.
Well, I checked on my WP-34S before posting, and it didn't work in programming mode for the two times I tried.
For instance, typing [h] + [XEQ] (GTO) [.] [0] [2] [5]
What I did get was two new program entries:
GTO 02
5
And so I wrongly assumed it was not working as indicated.
But now I have found out the issue: as I mentioned in another thread, my calculator has a lot of keyboard issues, so I found out one more failing key: The [.].
So it is the [A], [.], and one full row from [down] to [-].
I believe it is about time to scrap it and get another one